Electric Bicycle 24/36/48V Intelligent JN-G51 Display with USB Port E-Bike LCD Control Panel 5Pin Waterproof Plug Accessories Cycling Computer E-Scooter Ebike Display Modification Accessories

Function Description: 1、Display function Speed display, power-assisted gear display, power indication, fault indication, total mileage, single mileage, headlight display, single driving time display 2. Control, setting function power switch control, headlight switch control, 6Km/h point control, wheel diameter setting, maximum speed setting, idle Automatic sleep time setting, backlight brightness setting, voltage level setting, 3. Communication protocol: UART Display full content (full display within 1S of power on) Display content introduction 3.1 Headlight 3.2 Battery level display BATTERY 3.3 Multi-function display area Total Mileage 0D0, Single Mileage TRIP, Fault Code Error, Power WATT, Maintenance Maintain; DST T0 GO (not used yet) 3.4 Vehicle Mode POWER: Powerful mode Speed display area Maximum speed MAX, Average speed AVG Unit MPH.KM/H The meter will calculate the real speed according to the wheel diameter and signal data. 3.6 Vehicle status display area Vehicle status symbols and code meaning: : Digital voltage; : Brake alert; : Motor fault; Communication fault;: turnbuckle fault;: controller fault. 3.7 Fault generation obstacle Fault code (decimal) Fault status Remarks 0 Normal status 1 Reserved 2 Brake 3 Boost sensor malfunction (riding symbol) not realized here 4 6KM/H cruise 5 Real-time cruise 6 Ghost pool under pressure 7 Motor failure 8 Handlebar failure 9 Controller failure 10 Communication reception failure 11 Communication transmission error 12 BMS communication failure 13 Headlight fault 3.8 Settings PO1: Brightness of backlight, level 1 is the darkest, level 3 is the brightest; PO2: Mileage unit, O:KM;1:MILE; PO3: Voltage level: 24V, 36V, 48V, 6OV,64V Default 36Y; P04: hibernation time: 0, no hibernation; other numbers are hibernation time, range: 1-60; unit minutes; P05: booster gear: 0, 3-speed mode: 1, 5-speed mode: P06: wheel diameter: unit, inch; accuracy: 0.1 (No. 2 protocol); 5S protocol and J-LCD protocol wheel diameter Value for the digital code to indicate: 0:16 inch, 1:18inch, 2:20inch, 3:22inch, 4:24inch, 5:26inch, 6:700c, 7:28inch This parameter is related to the speed displayed by the meter and needs to be entered correctly; PO7: Number of speed measuring magnets: range: 1-100; This parameter is related to the speed displayed on the meter and needs to be input correctly; If it is an ordinary hub motor, directly input the number of magnets; If it is a high-speed motor, you also need to calculate the reduction ratio, input data = number of magnets × reduction ratio; For example: motor magnet steel number 20, deceleration ratio 4.3: input data is: 86 = 20 X 4.3 P08: speed limit: range 0-100km/h, 100 means no speed limit. The input data here indicates the maximum operating speed of the vehicle: e.g. enter 25, which means that the maximum operating speed of the vehicle will not exceed 25km/h; The drive speed is maintained at the set value, the Tolerance: earth 1km/h; (booster, turn handle are speed limit) Note: The value here is based on kilometers, when the unit setting is converted from kilometers to miles, the speed value of the display interface will be automatically converted to the correct value of miles, but the data of the speed limit value set at this menu under the miles interface is not converted and is not consistent with the actual display of the mile speed limit value; Note: The P09-P15 menus are only valid in the communication state. P09: zero start, non-zero start setting, 0: zero start; 1: non-zero start; P10: drive mode setting 0: power-assisted drive (decide how much power-assisted is output through the power-assisted gear, at this time the turnbuckle is invalid). 1: electric drive (driven by the turnbuckle, at this time the power-assisted gear is invalid). 2：Boost drive and electric drive coexist at the same time P11: Boost sensitivity setting Range: 1-24; P12: Boost start strength setting Range: 0-5; P13: Setting of booster magnet disk type: 5, 8, 12 grains of magnets. P14: Controller current limit value setting default 12A Range: 1-20A P15: Controller under-voltage value P16:0D0 clearing setting Long press up key for 5 seconds OD0 clearing P17:0: do not enable cruise, 1: enable cruise; auto-cruise optional (only valid for protocol No. 2) P18: display speed proportional adjustment Range: 50%~150%, P19:0 gear enable bit, 0: with 0 gear, 1: without 0 gear P20:0:No.2 protocol 1:5S protocol 2:J-LCD protocol 3:standby Packaging: 1*Display

• ★Kind tips: JN LCD G51 is a smart waterproof display, compatible with 24V/36V/48V voltage, Please carefully check the label on the controller so that it won't work after purchase. Our No.2 Protocol dispaly need to be used with a waterproof No.2 Protocol controller and 1 to 4 cable.
• ★Multi Function: The G51 display with USB has a variety of functions, which can be used as a trip computer and control the entire electric bicycle system after conversion. The function can be realized by connecting the meter socket of the display screen to the instrument interface of the controller.
• ★Wide Range of Application: The LCD G51 Display Control Panel is suitable for 22.2mm / 0.9in handlebars, is perfect accessories for electric bicycles etc.
• ★Battery Level Display: This lcd panel is compatible with 36V and 48V voltage, intelligent power display, true battery power display, real time recording power consumption, to ensure riding mileage. If for PAS is installed, this display allows the rider to choose the level of assistance they want, which is more convenient for riding.
• ★For Most Handlebars: The LCD G51 display control panel is suitable for 22.2mm / 0.9in handlebars, is perfect accessories for electric bicycles,etc. Please feel free to contact us if you have any question.We are committed to providing you with better products and services